DIY | Build Your Own Shelf

After building my first ever project (my porch table), I got the bug and wanted to try my hand at building something else. Because … if I can build a table I can build anything right? Well …. let’s just say this one was a good effort. For my porch table project I used a project plan provided by someone who knew what they were doing. This time, I totally winged it. I didn’t have plans drawn up… I didn’t copy someone else’s. I just had an idea in my head as to what I wanted – some combination of metal and wood. I also scoured online for tutorials and how-to’s and they all weren’t very helpful. But I’d built a table so of course I could build a measly little shelf! Turns out … it was harder than it seemed! The top shelf is a little wobbly and the pipes are a little uneven/crooked … but to the naked eye it looks ok.

On to Home Depot Wes and I went …. yes I dragged Wes into this and he went along … kicking and screaming! He hates Home Depot. A lot. In fact, he tweeted the following while we were having what I thought was so much fun shopping for our supplies:

How could Wes and I be more opposite? I think Home Depot is fun! So anyway, to build yourself a table like mine you would need the following supplies:

Cost: $30



  • 1/2 inch black metal pipe
  • Wood cut to size
  • 3/4 inch drill bit
  • Rubber Bands
  • Stain for the wood
  1. Now I have to admit the instructions are not very good, because like I said – we winged it. Wes and I measured out where the holes needed to go, drilled the holes, realized the holes in each piece of wood didn’t line up, tried to make the holes bigger so they’d line up, yada yada yada.
  2. Then we pushed the pipe into the middle shelf and to keep the middle shelf from slipping down the pole (not that it would because the holes were so tight), we placed rubber bands under the shelf.
  3. Then we shoved and twisted the pipe into the bottom shelf, and placed the top shelf on top.
The end. Again I would not recommend that anyone actually build these shelves the way I’ve instructed – but if you are itching to build a shelf and this will do.. then go for it!
(check out these fancy rubber bands holding up the middle shelf)
Here are some photos and links to the blogs of the shelves that inspired me to build my shelf:

Design | Mr & Mrs Bedroom

What’s better than 3D cardboard letters wrapped in yarn for that extra touch at your wedding? Actually being able to use them again as home decor post-wedding! I created MR and MRS for the head table at my wedding and TREAT for the Ice Cream table. I’ve been able to take both and re-use them for home decoration. MR and MRS I put above our bed on our respective sides and with the TREAT I placed EAT in the kitchen above the stove. I know – I’m REALLY clever, eh?

(wedding photo credits)

Upcycle | bad to fab stools

Cost: $35 stools

I recently went to a local vintage flea market with one goal in mind. Find vintage barstools. My apartment has a bar in front of the kitchen, and I needed the extra seating for my bar height dining room table. Luckily, I found 3 barstools for $10 apiece. The only problem is that while they were vintage … they were bad vintage. The wood stain was badly splotched and peeling, there was a fruit painted on each stool (pear, apple, and plum) with legs spray painted to match (yellow for the pear, red for the apple, and purple for the plum). Not quite the look I was going for.

So I gave it a simple makeover to suit my style more. I spray painted the legs a bronze metal color, sanded the wood to remove the old stain and paint, and restained the top. (You’ll recognize this stain color from my DIY table)
The results:

DIY Tutorial | Beginners Guide to Building a Table

Cost: $50 

I’ve lived in my apartment since getting married for 4 months now and my small 2nd story apartment porch has not been a priority for me. That is until I planned a Fall Party for this upcoming weekend. My sad porch only recently featured 2 barrels filled with mums and a hanging planter. Nowhere to sit and relax to enjoy the outdoors.

There are a lot of things on my bucket list of things I’d like to accomplish sometime in my life … and building something from scratch was definitely one of them. I’ve never taken a woodworking class, never even watched someone build with wood before. But this weekend I decided to replicate Diary of a Preppy Mom’s foyer table which I had discovered on Pinterest. I tweaked a few things to her design to make a bigger table for my porch. Seriously, if I can do this … so can you! It was much easier than I expected… and also made me realize how overpriced furniture is.

Here it is! Now I just need to get some chairs for the table…

To start I had to break out my math skills and determine all of the measurements. This porch table is a bit bigger than the tutorial’s foyer table. So I chose the following measurements. Through google searching, I found that a standard table is 30″ tall and a bar table is around 40″ tall.

  • Four
  • -> 28″ 1×3 pine (the legs)
  • Four -> 4′ 1×6 pine (for the top)
  • Two -> 16″ 1×6 pine (for the short sides of the “box”)
  • Two -> 3’10” 1×6 pine (for the long sides of the “box”)
  • One -> 3’5″ 1×6 pine (for the long side that will go in between two of the legs)

You’ll also need the following:

  • Powerdrill
  • #6x 3/4′ Construction Screws
  • #8x 1 1/4′ Construction Screws
  • 4 brackets

I don’t have my own table saw and don’t plan to purchase one anytime soon, so I went to Home Depot and selected my wood (I was pretty excited as you can see) and then they cut it down to size. They have the cutting listed as 50 Cents a cut, but for some reason they only charged me for the wood.

When I got home to get started, these two came over for moral support!

To start assembling you will want to take the two 16″ 1×6 and the two 3’10” 1×6 and fit them together in a square. Then apply the brackets to the corners and screw them in with the 3/4″ screws.

I then screwed the four 28″ 1×3 legs (2 screws on each) to each side of the box and then placed the one 3’5″ board in between the front two legs to give it that seamless look. Here is what it looks like without the leg. As you can see – the leg will fit perfectly next to it. I didnt do the same to the back since nobody would see it.

And the last step is to screw the four 4′ 1×6 boards to the top! I made the box underneath smaller than these four boards so that there will be an overhang for the top.

And that’s it! Easy, right?? And for only $50! I dont think I’ll ever be able to purchase wood furniture in-store ever again. With the table fully stained, it turned out a little more country chic than I like, so I may paint the legs and sides white and leave the very top stained to give it a more modern look. But that is for another day.

Upcycle | Dresser to Buffet Table

How to stain a buffet table with Minwax Polyshades stain and Polyurethane in 1 step
I’ve only roomed with 4 different people in my life before marrying Wes. Stacie (Reeder) Eldridge, Amy Babbitt, Liz Talcott, and my mom/sister. In each of these arrangements, I was always the one who provided most of the furniture/decor since those items mattered the most to me. When Wes and I moved into our apartment a couple months ago, I brought all of my furniture and decor with me from all of my previous living arrangements. To my surprise, my belongings didn’t fill the entire apartment as it usually would in my other homes. My apartment isn’t any bigger than past homes. The difference I believe is that the walls of this apartment are all pure white with vaulted ceilings. No cozy paint colors or lower ceilings to offer that smaller space feel. Not that I’m complaining – I LOVE vaulted ceilings and it is a new challenge for me to work with decorating via a white canvas.
One of the worst eye sores was my dining room. We have this stand-alone fireplace that separates the living room from the dining room and all I had for the dining space was my high-boy dining room table. I immediately knew what was needed to uplift the space – a buffet table! I have seen a lot of creative buffet tables on pinterest and blogs – most being dresser makeovers. I love how buffet dressers for the dining room allow extra room for displaying decor and space for serving food or drinks.
Let the challenge begin! I had a few goals in mind. 1) I knew I didnt want to purchase a brand new dresser 2) I was looking for something with character 3) I didn’t want to spend more than $200. After searching Craigslist for weeks and weeks, I stumbled upon a beautiful 60’s  bedroom set that someone was selling for $600 total. After a little bit of negotiating, I was able to talk her down to selling me a long “buffet” dresser + a tall matching dresser for $200 total. Not bad!
BEFORE | Unfortunately, I didn’t take photos of the buffet dresser before I made it over, but here is a photo of the matching tall dresser.
AFTER | this is the results of the buffet dresser once I was done with it.
I love the results! But it definitely wasn’t easy getting there! I had to do a lot of research online around how to sand and stain laminate furniture. There are 2 kinds of laminate furniture – 1) the high gloss thin laminate that is almost impossible to paint over without it easily chipping later and 2) thick laminate that is easier to sand and stain. Thankfully my dresser was of the #2 variety.
Here’s what you need to re-stain laminate furniture.
1) low grain sandpaper or sandblocks
2) a strong arm
3) high grain sandpaper or sandblocks
4) a strong arm
5) dustcloths
6) stain
7) stain paintbrush
8) patience – 12 hours between each coat
After sanding and sanding and sanding to remove the high gloss finish, it was ready for some stain. At first I tried regular wood grain stain on the dresser with little results. Because of the laminate, it barely tinted the wood darker, and I realized I’d have to add 500 coats to get it to the desired color. So I went back to the store and picked up the hardest stain to work with EVER! Minwax’s polyshades stain and polyurethane in 1 step!
After some trial and error and some resanding to remove my errors, I finally figured out how best to work with this stain for the best results. You must purchase a paint brush that is specifically made for wood staining – do NOT use the sponge brushes. Dip your brush into the stain and slide it against the edge to remove access. Start at the top of your wood section and move lightly across the wood grain in one stroke. I applied 3 coats total to my dresser – otherwise it would have turned out very streaky. You must allow the stain to dry overnight before adding more coats.
Tip | Do NOT move back and forth as it will build up sticky residue with inconsistent blotching. You must move in one direction the entire time. You also need to work as quickly as possible as it begins to dry quickly and can gum up. My friend, Jasmin, experienced the “bad” of what could happen if you don’t apply this tricky stain properly. She used it on an ikea hack project:
Tip | If you accidentally stain your carpet – as I did many times – it is actually very simple to remove it! I had some DW-40 lying around, and if you spray it directly into the stained carpet and rub it out with a paper towel – it removes it like magic! You cant even find the spots  if you were even looking for them anymore!
I also took the knobs that were rusting and spray painted them in a metallic silver to give it that shiny new look!
The finished product! Just what my dining room needed.